Second problem: After booting the new kernel I disabled that module and then I had no more keyboard.
The same disk can be used for 32 and 64 bit installs.įirst problem: I didn't have that module, so I built a new kernel to have that module (instead of in-kernel).
To install Gentoo I use sysrescuecd.Based on Gentoo,has firefox to browse Gentoo docs and mc to browse (and edit) files. (see the Start Here sheet), turn to this Quick Guide and your on-screen User’s Guide for. Epson Perfection® V600 Photo Start Here Point de départ Read these instructions before using. USB3 didn't exist at the time this scanner was made. 4113963 Rev.0 4113963 Rev.0 4113963 Rev.0 4113963 Rev.0 1-F C 1-F M 1-F Y 1-F K Epson Perfection® V300 Photo Start Here Guía de instalación. I've had problems with an Epson combi much like yours.
It's also not limited to xsane, it's the same with scanimage and other tools. I've been trying different gentoo-sources, now I'm at 3.12.13, but it didn't change anything. It initializes the scanner (sled is moving) and then some seconds nothing happens.ģ) Instead of the xsane window an error message pops up:įailed to open device 'epkowa:interpreter:003:006': Error during device I/O.Ĥ) If I now run xsane again its window pops up most of the time, but sometimes I have to power off the scanner and start at (1) again, until it works. usb 3-4: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframesĢ) I run xsane. usb 3-4: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-4: New USB device found, idVendor=04b8, idProduct=0131 usb 3-4: new high-speed USB device number 6 using xhci_hcd
After buying a new PC and installing 64bit Gentoo I can't use the scanner "the easy way":ġ) I power on the scanner and it's detected: I've been using the named scanner for years without any problem on my old PC (32bit Gentoo). Posted: Sat 9:44 am Post subject: Strange Epson Perfection V300 Photo (USB) problem Gentoo Forums Forum Index Kernel & Hardware Strange Epson Perfection V300 Photo (USB) problem
Openrc-0.17, ~vanilla-sources, ~nvidia-drivers, gcc-10.Gentoo Forums :: View topic - Strange Epson Perfection V300 Photo (USB) problem My epson perfection v700 scanner (that allows me to scan photos, negatives, documents, etc.) and that I paid over 800 for) stopped working with teh latest update two days ago. Ryzen 3700X, Asus Prime X570-Pro, 32 GB DDR4 3200, GeForce GTX 1660 Super Same versions of all the packages save media-gfx/sane-backends-1.0.21 I'm seeing the same thing on the Perfection V30 Is there any way to check or reset it status with sane? It seems that scanner stuck in some status where it can't be turned off. (the same versions in x86_64 and i386 environment) I have the same problem in x86_64 and i386 environment. Only after I boot in Windows XP and try windows tool for scanning, power button begins to work well. The only way to turn it off is to plug off the power cord. I can't turn it off even after I shut down the PC. It should be shut down by pressing power button for 3 seconds, but it don't. Before any actions with scanner I can turn it on and off by power button, but after doing something (iscan, xsane, scanimage -L), I can't turn it off by power button. Make sure you press the Power button for 3 seconds to turn off. I successfully installed it, and scanning process going just fine. Home Support Scanners Perfection Series Epson Perfection V300 Photo.
I have a problem with my scanner Epson Perfection V300 Photo: Posted: Sat 11:43 am Post subject: Can't turn off scanner Epson Perfection V300 Photo Gentoo Forums :: View topic - Can't turn off scanner Epson Perfection V300 PhotoĬan't turn off scanner Epson Perfection V300 Photo